| Age | Commit message (Collapse) | Author |
|---|
|
RISC-V privilege specification does not specify how to encode the event ID.
Therefore, each platform is allowed to customize its own encoding rule.
The common encoding methods are as follow, directly assigning a number to an
event, or every bit in the mphmevent CSR controls one specified event or
mixes the above two methods.
To enable OpenSBI to support the above three encoding methods simultaneously,
this patch repurpose the dt property "riscv,raw-event-to-mhpmcounters". The
"riscv,raw-event-to-mhpmcounters" will describes the one or multiple raw
events that could be counted by a set of counters. But, the column number
of "riscv,raw-event-to-mhpmcounters" is extended from 2 to 3. The 1st column
(64bit) is the ID of the raw events. The 2nd column (64bit) represents a
select_mask now to represent the bits used for event ID encoding.
If a platform directly encodes each raw PMU event as a unique ID,
the value of select_mask will be 0xffffffff_ffffffff.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Signed-off-by: Atish Patra<atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
Add support for the UART provided by the LiteX SoC
framework (https://github.com/enjoy-digital/litex),
based on its FDT info (described in the Linux tree at
Documentation/devicetree/bindings/serial/litex,liteuart.yaml).
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
Minimum SiFive I2C driver to read/send bytes over I2C bus.
This allows querying information and perform operation of onboard PMIC,
as well as power-off and reset.
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Tested-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
|
|
FDT based I2C framework on the top of I2C library.
The drivers are probed on demand by fdt_i2c_adapter_get
function.
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Tested-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
|
|
Helper library to keep track of registered I2C adapters,
identified by dts offset, basic send/read functions and
adapter configuration (enable, set dividers, etc...).
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Tested-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
|
|
Move driver init code to separate function, so it can be reused
elsewhere.
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Tested-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
|
|
Make gpio_system_reset_check return priority instead of just true/false.
Make default 128 priority for reset/shutdown.
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Tested-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
|
|
As per the DT schema rules, the prefix should be vendor. As the PMU
properties are generic for all vendors, change the prefix to riscv
instead of pmu.
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
|
|
Some platforms such as hifive unmatched doesn't implement mcountinhibit
csr. However, it has hardware events that can be monitored using 2
hpmcounter it has (i.e. mhpmcounter3 & mhpmcounter4).
Currently, PMU extension disabled if mcountinhibit is absent. That's not
really necessary as long as the supervisor OS keeps track of the delta
value of the counters. Without mcountinhibit, the delta value won't be
entirely accurate because the counters are freely running. However, that
should be fine to produce an approximate counter value which can help
performance analysis. Perf sampling won't work though as sscof extension
is not present in hifive unmatched.
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
|
|
The initialization of a reset driver may fail for various reasons, like
a PMIC based reset driver not finding the required I2C driver. The return
code of the init routine may take other error values than -ENODEV.
If the initialization of a reset driver fails, this should not lead to the
board hanging. It is enough that the reset driver does not call
sbi_system_reset_add_device() to avoid invoking the driver for a device
that could not be initialized.
Change the return type of fdt_reset_init() to void.
Print a message if an error occurs.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Dong Du <Dd_nirvana@sjtu.edu.cn>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
Convert static array to sbi_list.
This removes size limitation, makes add/remove more efficient and
saves space.
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
This simply adds an helper to get fdt address which is more explicit than
sbi_scratch_thishart_arg1_ptr.
Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
Now that sbi_system support multiple system reset devices, we should
register separate devices for GPIO restart and GPIO poweroff because
DT describes these as separate devices with different compatible
strings.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Dong Du <Dd_nirvana@sjtu.edu.cn>
|
|
The T-HEAD PLIC implementation requires setting a delegation bit
to allow access from S-mode. Now that the T-HEAD PLIC has its own
compatible string, set this bit automatically from the PLIC driver,
instead of reaching into the PLIC's MMIO space from another driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
To support different handlers for different types of resets, we are
adding a sbi_list of restart handlers.
Instead of sbi_system_reset_set_device we use
sbi_system_reset_add_device to reflect the actual meaning.
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
The GPIO reset driver supports reset and poweroff. But not all boards
support both. gpio_system_reset_check() must detect this situation.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
We should use sbi_timer_mdelay() instead of custom gpio_mdelay() in
the gpio reset driver.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Xiang W <wxjstz@126.com>
|
|
Generic mdelay() and udelay() functions can be provided by the
sbi_timer framework if timer frequency is available in the timer
instance provided by the platform support or timer driver.
This patch adds timer frequency (timer_freq) member in the
struct sbi_timer_device for above purpose.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Xiang W <wxjstz@126.com>
|
|
We add fdt_parse_timebase_frequency() function which can be used
by ACLINT mtimer driver and platform code to get timebase frequency.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Xiang W <wxjstz@126.com>
|
|
One of the watchdogs in the D1 SoC provides a "soft reset" function,
which allows software to immediately reset the entire SoC. Add a driver
so it can implement the SBI system reset function.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
In preparation for adding a new fdt_reset driver, ensure the existing
lists are sorted alphabetically.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
We simplify MTIMER synchronization as follows:
1) Detect MTIMER devices with unique (or non-shared) MTIME
register at boot-time
2) Select first MTIMER device with no associated HART as our
reference MTIMER device
3) Only synchronize MTIMER devices with unique (or non-shared)
MTIME register using reference MTIMER device
4) Directly update the MTIME register at time of synchronization
because MTIME is a read/write register.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
We can have ACLINT MTIMER devices which only support 32-bit MMIO
accesses on RV64 system so this patch adds a boolean DT property
"mtimer,no-64bit-mmio" to detect this from MTIMER DT node.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
The fdt_parse_aclint_node() is used to parse DT node for SiFive
CLINT, ACLINT MTIMER, and ACLINT MSWI devices.
The ACLINT MTIMER has undergone following changes:
1) MTIMER DT node now requires separate addresses in for MTIME
register and MTIMECMPx registers in the reg DT property.
2) MTIMER DT node might have no interrupts-extended DT property
when the MTIMER device has no associated HARTs (i.e. the
MTIMER device has no MTIMECMPx registers)
This patch extends fdt_parse_aclint_node() to handle above
mentioned changes in ACLINT MTIMER DT bindings.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
We add "index" parameter to fdt_get_node_addr_size() API so that
calling function can specify index of desired register set. This
will allow fdt_get_node_addr_size() to handle DT nodes with
multiple register sets.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
We extend the ACLINT library to support separate base addresses
for MTIME and MTIMECMP registers.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
The maximum address and size encoded in DT are 64-bit numbers, so we
should use uint64_t for 'addr' and 'size' in fdt_get_node_addr_size().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
The generic GPIO reset driver has two entries in the match table:
"gpio-poweroff", "gpio-reset". Only the first entry is considered by
fdt_reset_init().
Define "gpio-poweroff" and "gpio-reset" as compatibility strings of two
separate reset drivers. They still can share code.
Fixes: e3d6919d10d7 ("lib: utils/reset: Add generic GPIO reset driver")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
The value of variable current_driver is unused. Remove the variable.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
We add generic GPIO reset driver inspired from gpio-restart
and gpio-poweroff drivers of Linux kernel.
Signed-off-by: Green Wan <green.wan@sifive.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
We add a minimal SiFive GPIO driver so that we can do GPIO based
system power-off and reset.
Signed-off-by: Green Wan <green.wan@sifive.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
We add a simple FDT based GPIO framework which is built on top
of generic GPIO library. The phandle of FDT GPIO chip DT node
is treated as unique GPIO chip ID required by the generic GPIO
library. The FDT based GPIO chip drivers will be probed on-demand
from fdt_gpio_pin_get() called by the GPIO client drivers.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
We add generic GPIO configuration library which is independent of
hardware description format (FDT or ACPI). The OpenSBI platform
support or GPIO drivers can register GPIO chip instances which
can be discovered and used by different GPIO clients. Each GPIO
chip instance has a unique ID which can be used by GPIO clients
to lookup GPIO chip instance.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
The libfdt project does not have a generic API to parse phandle
with args from a DT node so we add fdt_parse_phandle_with_args()
for this purpose. This new API will be useful to FDT based drivers.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
We only need libgcc for 64-bit division on RV32. Whilst GCC toolchains
bundle libgcc, Clang toolchains tend not to ship libclang_rt.builtins
given every compiler is a cross-compiler for every target and so you
would need a silly number of builds of it, with only the native library
available; only vendor-provided Clang toolchains specifically for bare
metal cross-compiling are likely to provide it.
Thus, import part of FreeBSD's implementation of the division support
functions needed and stop linking against libgcc.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
|
|
The PMU DT node bindings are defined in docs/pmu_support.md
Add few fdt helper functions to parse the DT node and update the
event-counter mapping tables.
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
|
|
Unify all the file and function names of 'sifive_test' device, to use
the same prefix. This is also a preparatory patch for upcoming sifive
reset device.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
The ACLINT devices are backward compatible with SiFive CLINT
so we replace all CLINT library usage in various platforms
with ACLINT library. As a result of this replacement, the
CLINT library is not used by any part of OpenSBI hence we
remove it.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Xiang W <wxjstz@126.com>
|
|
We add a new FDT based ACLINT MTIMER driver which works for
both CLINT device and standalone ACLINT MTIMER device.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Xiang W <wxjstz@126.com>
|
|
We add a new FDT based ACLINT MSWI IPI driver which works for both
CLINT device and standalone ACLINT MSWI device.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Xiang W <wxjstz@126.com>
|
|
We add fdt_parse_aclint_node() which can parse both ACLINT and
CLINT DT nodes. This means fdt_parse_clint_node() is not required
anymore so we remove it as well.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Xiang W <wxjstz@126.com>
|
|
We add common ACLINT MSWI library similar to the CLINT library
so that OpenSBI platforms can use it.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Xiang W <wxjstz@126.com>
|
|
We add common ACLINT MTIMER library similar to the CLINT library
so that OpenSBI platforms can use it.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Xiang W <wxjstz@126.com>
|
|
Sync with libfdt v1.6.1 release source codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
If property csr-copy does not exist, fdt_getprop() will return NULL and cnt
will have a random value from the stack.
Call clone_csrs() only if cnt is initialized to a non-zero value.
Fixes: 49e422c5ad7a ("lib: utils: reset: Add T-HEAD sample platform reset driver")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
The value of the /chosen/stdout-path devicetree property is used to
determine the UART used by openSBI. According to the devicetree
specification the value may contain a hyphen, e.g.
chosen {
stdout-path = "/serial@f00:115200";
};
If the character ':' is present, it terminates the path of the device.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
|
|
We should try other FDT drivers when we see SBI_ENODEV returned
by cold_init() of FDT driver.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Xiang W <wxjstz@126.com>
|
|
Use strncmp() instead of strcmp() in __fixup_find_domain_offset()
so that it compiles fine when linking with external firmware (such
as EDK2).
Signed-off-by: Daniel Schaefer <daniel.schaefer@hpe.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Abner Chang <abner.chang@hpe.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
When SBI is built by external firmware, we need to use their functions,
defined in libfdt_env.h.
Just like 2cfd2fc9048806353298a1b967abf985901e36e8
Signed-off-by: Daniel Schaefer <daniel.schaefer@hpe.com>
Reviewed-by: Abner Chang <abner.chang@hpe.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
|
we want to use sbi_strncpy as strncpy in the OpenSBI implementation for
libfdt.
Just like 2845d2d2cf4fb74a89452ba223995aa4a118c07e
Signed-off-by: Daniel Schaefer <daniel.schaefer@hpe.com>
Reviewed-by: Abner Chang <abner.chang@hpe.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
|
